EN 12390-1 Testing Equipment

EN 12390-1 testing equipment for concrete test molds workflows in concrete laboratories.

Test Method Context

EN 12390-1 is commonly used by laboratories that need a standards-led concrete test molds workflow for concrete. The method is usually not just a machine requirement; it also defines how samples are prepared, conditioned, measured, reported, and compared against project or agency acceptance criteria. Laboratories searching by EN 12390-1 normally need equipment that can hold the correct specimen format, maintain stable control conditions, support repeatable operator routines, and produce data that can be reviewed by clients, road authorities, university supervisors, or third-party inspection teams. Lithostek treats the standard page as a method map: it connects the official EN reference to the practical laboratory steps, the matching equipment families, and the configuration questions that should be answered before purchase.

Equipment Selection

For equipment selection, start with the material, specimen size, required capacity, control accuracy, and daily sample volume. EN 12390-1 equipment for concrete test molds often requires more than the primary tester; laboratories may also need preparation tools, conditioning equipment, calibration accessories, data output, spare parts, and operator training. The matching Lithostek systems for this page include LS-CM-P100, LS-CM-P100-2, LS-CM-S100, LS-CM-S200, LS-CYL-P1020. These products are organized around CONCRETE workflows so laboratory teams can compare automation level, measurement resolution, environmental control, safety enclosure, reporting format, and after-sales support without leaving the standard-number path.

Concrete Test Molds, Moulds & Specimen Forms

Quality Control Notes

Quality-control teams should confirm the latest official EN 12390-1 document before finalizing a tender or laboratory SOP, because tolerances, conditioning details, and reporting fields can change by edition or local specification. In practice, the equipment quotation should reference the target standard, destination market, specimen type, throughput, power supply, calibration route, and any required acceptance test before shipment. Lithostek can review these details and configure the system around specimen preparation, controlled testing, reporting, calibration, and compliance review, helping laboratories avoid under-specified machines that pass a catalog comparison but fail daily repeatability or documentation requirements.

Related Standards

Related methods are useful when a laboratory needs a complete package rather than one isolated instrument. A EN 12390-1 request may sit next to other ASTM, AASHTO, EN, ISO, or local standards covering sample preparation, conditioning, strength, durability, dimensional checks, or reporting traceability. Use the standards index to move from EN 12390-1 into adjacent method pages, then open the linked product pages to compare the equipment scope, accessories, and application notes. This keeps equipment selection tied to the test method instead of relying only on generic category names.

Matching Lithostek Equipment

LS-CM-P100

Plastic Concrete Cube Test Mold (100 x 100 x 100 mm)

Reusable engineering plastic cube mold for casting 100 x 100 x 100 mm concrete specimens. Configured for 100 mm concrete cube compressive-strength specimen casting with the mold geometry, construction, and verification documents confirmed against EN 12390-1, EN 12390-2, BS 1881-108.

LS-CM-P100-2

Two-Gang Plastic Concrete Cube Test Mold (100 x 100 x 100 mm)

Reusable engineering plastic cube mold for casting 2 cavities, each 100 x 100 x 100 mm concrete specimens. Configured for paired 100 mm concrete cube specimen production with the mold geometry, construction, and verification documents confirmed against EN 12390-1, EN 12390-2, BS 1881-108.

LS-CM-S100

Steel Concrete Cube Test Mold (100 x 100 x 100 mm)

Machined steel cube mold for casting 100 x 100 x 100 mm concrete specimens. Configured for reference-grade 100 mm concrete cube specimen casting with the mold geometry, construction, and verification documents confirmed against EN 12390-1, EN 12390-2, BS 1881-108.

LS-CM-S200

Steel Concrete Cube Test Mold (200 x 200 x 200 mm)

Machined steel cube mold for casting 200 x 200 x 200 mm concrete specimens. Configured for large-format 200 mm concrete cube specimen casting with the mold geometry, construction, and verification documents confirmed against EN 12390-1, EN 12390-2, BS 1881-108.

LS-CYL-P1020

Reusable Plastic Concrete Cylinder Mold (100 x 200 mm)

Reusable engineering plastic cylinder mold for casting 100 mm diameter x 200 mm height concrete specimens. Configured for metric concrete cylinder specimen casting with the mold geometry, construction, and verification documents confirmed against ASTM C470/C470M, ASTM C31/C31M, ASTM C192/C192M, EN 12390-1.

LS-CYL-P1530

Reusable Plastic Concrete Cylinder Mold (150 x 300 mm)

Reusable engineering plastic cylinder mold for casting 150 mm diameter x 300 mm height concrete specimens. Configured for metric concrete cylinder specimen casting with the mold geometry, construction, and verification documents confirmed against ASTM C470/C470M, ASTM C31/C31M, ASTM C192/C192M, EN 12390-1.

LS-CYL-S1020

Steel Concrete Cylinder Mold (100 x 200 mm)

Machined steel cylinder mold for casting 100 mm diameter x 200 mm height concrete specimens. Configured for reusable laboratory concrete cylinder specimen casting with the mold geometry, construction, and verification documents confirmed against ASTM C470/C470M, ASTM C31/C31M, ASTM C192/C192M, EN 12390-1.

LS-CYL-S1530

Steel Concrete Cylinder Mold (150 x 300 mm)

Machined steel cylinder mold for casting 150 mm diameter x 300 mm height concrete specimens. Configured for reusable 150 x 300 mm concrete cylinder specimen casting with the mold geometry, construction, and verification documents confirmed against ASTM C470/C470M, ASTM C31/C31M, ASTM C192/C192M, EN 12390-1.

LS-CYL-S1632

Steel Concrete Cylinder Mold (160 x 320 mm)

Machined steel cylinder mold for casting 160 mm diameter x 320 mm height concrete specimens. Configured for european and project-specific concrete cylinder casting with the mold geometry, construction, and verification documents confirmed against EN 12390-1, EN 12390-2.

LS-BM-P101040

Plastic Concrete Beam Test Mold (100 x 100 x 400 mm)

Reusable engineering plastic beam mold for casting 100 x 100 x 400 mm concrete specimens. Configured for concrete flexural beam and prism specimen casting with the mold geometry, construction, and verification documents confirmed against EN 12390-1, EN 12390-2, ASTM C192/C192M.

LS-BM-S101050

Steel Concrete Beam Test Mold (100 x 100 x 500 mm)

Machined steel beam mold for casting 100 x 100 x 500 mm concrete specimens. Configured for concrete flexural beam and prism specimen casting with the mold geometry, construction, and verification documents confirmed against EN 12390-1, EN 12390-2, ASTM C192/C192M, ASTM C78/C78M.

LS-BM-S151560

Steel Concrete Beam Test Mold (150 x 150 x 600 mm)

Machined steel beam mold for casting 150 x 150 x 600 mm concrete specimens. Configured for concrete flexural-strength beam specimen casting with the mold geometry, construction, and verification documents confirmed against EN 12390-1, EN 12390-2, ASTM C192/C192M, ASTM C78/C78M.

LS-BM-S151575

Steel Concrete Beam Test Mold (150 x 150 x 750 mm)

Machined steel beam mold for casting 150 x 150 x 750 mm concrete specimens. Configured for long-format concrete flexural beam specimen casting with the mold geometry, construction, and verification documents confirmed against EN 12390-1, EN 12390-2, BS 1881-108.

LS-MS-METAL-266

Metal Concrete & Mortar Mold Set (2 + 6 + 6 Molds)

Metal laboratory mold set containing two triple-gang 70.7 mm mortar cube molds, six 150 mm concrete cube molds, and six 150 x 300 mm concrete cylinder molds with base plates and clamping hardware.

LS-PM-P1530

Plastic Concrete Prism Test Mold (150 x 150 x 300 mm)

Reusable plastic concrete prism test mold for casting 150 x 150 x 300 mm specimens in routine QC and laboratory preparation workflows.

LS-PM-C150A

Plastic Concrete Cube Test Mold, Tapered Body (150 x 150 x 150 mm)

Tapered-body reusable plastic concrete cube test mold for casting 150 mm cube specimens in daily laboratory workflows.

LS-PM-C150B

Plastic Concrete Cube Test Mold, Ribbed Body (150 x 150 x 150 mm)

Ribbed-body reusable plastic concrete cube test mold built for daily 150 mm specimen preparation and demolding workflows.

LS-PM-C150C

Plastic Concrete Cube Test Mold, Bolted Frame (150 x 150 x 150 mm)

Bolted-frame plastic concrete cube test mold for 150 mm specimen casting and repeatable demolding workflows.

LS-MOLD150

Heavy-Duty Steel Concrete Cube Test Mold (150 x 150 x 150 mm)

Precision-machined steel concrete cube test mold for 150 x 150 x 150 mm specimens, with rigid structure and secure locking hardware for reference-grade casting.